How do I reset my Rheem water heater?
How do I reset my Rheem water heater?
Turn the water heater’s gas valve switch to the “OFF” position, wait for a few seconds and then flip the switch to the “ON” position to reset the system. The water heater’s gas valve is located near the bottom of the unit and connects to your home’s natural gas line.
How do you troubleshoot a Rheem tankless water heater?
1) Turn off all hot water faucets (2) Power off: At remote control, turn off water heater by pressing Power on/off button (3) Power on: Wait 5 minutes and press Power on/off to turn on water heater (4) Turn on hot water faucet and check for error display (5) repeat if necessary (6) If problem continues, read error …
How do you fix a Rheem tankless water heater Code 29?
There may also be restricted air flow around the unit. Call for service. Rheem fault code 29 – This code indicates that the heat exchanger outlet temperature is too low. By cleaning the heat exchanger air inlet, the problem is typically resolved.
Why is my Rheem tankless water heater beeping?
A water heater may sound a beep to warn that there is a water leak. The beeping may be initiated by a water heater shutoff feature, a flood prevention device. Beeping may also signal a gas leak. Low Fuel.
Why is my Rheem water heater not working?
Check the power supply to the water heater. Check to see if a fuse has blown or a circuit breaker is tripped. Replace the fuse or reset the breaker. Ensure that the disconnect switch, if used, is in the on position.
Why does my Rheem water heater keep shutting off?
If your power vent water heater keeps shutting off, the thermocouple could be damaged, dirty or bent. Inspect the thermocouple. If it is damaged, replace it. If dirty, let it down for cooling and then clean.
How do I fix error code 13 on Rheem?
Error Code 13
- Check that the air intake and exhaust venting is correctly installed and in good working order.
- Inspect and remove any blockage from the venting and where the vent terminates outside.
- Check and verify that the altitude settings reflect your location.
- Check the Flame Rod FL-24.
- Check the Blower Motor.
What does code 13 mean on a Rheem tankless water heater?
Error code 13 is incoming air supply or outgoing vent. This applies to gas water heaters. As air enters the combustion chamber, the sensor reads that air quality is sufficient for combustion. If incoming air or outgoing vent are not correct, then tankless sensors shut down the burner.
How do you fix code 13 on a Rheem tankless water heater?
An Error Code 13 will only display on Indoor Rheem Tankless systems.
- Check that the air intake and exhaust venting is correctly installed and in good working order.
- Inspect and remove any blockage from the venting and where the vent terminates outside.
- Check and verify that the altitude settings reflect your location.
Why is my Rheem hot water not working?
Firstly, check the power supply to your hot water unit. Check if the safety switch is ON at your switchboard. Also, check your circuit breaker and fuse. If they are all working as expected, the problem could be because of high water demand.
Why does my new water heater keep turning off?
If your gas water heater keeps shutting off, the thermocouple could be dirty, bent or damaged. The thermocouple is usually easily visible next to the pilot light. Inspect the thermocouple to determine if it is dirty or damaged in some way. If it is dirty, turn off the gas to allow the thermocouple to cool.
What does the Rheem error code P1 mean?
Rheem error code P1 means the water flow rates have fallen below 0.66 GPM for more than 5 seconds. If your Rheem displays an error code P1 the water flow rates are not sufficient for the main burner ignition.
What does it mean when Rheem says error code 03?
If your Rheem tankless water heater is showing an error code 00, it must be restarted. Close the hot water taps and remove or turn off the circulation pump if there’s any installed. Rheem error code 03 means there is a problem with the manifold control. Rheem error code 03 is found on units with MIC-180 or EZLink.
What does code 16 mean on Rheem water heater?
Rheem fault code 16 – This is an over temperature warning which could indicate a possible clogged heat exchanger. Click to see full answer. Herein, how do I reset my Rheem tankless water heater? Begin with turning the hot water tap off. Take the remote control and turn it off as well.
What does the Rheem error code 65 mean?
Rheem error code 65 means there is a problem with the water volume control. While troubleshooting, Rheem error code 65, confirm the unit receives enough water and all wiring connections are in good working condition and tight.