What is the default password for HP Procurve switch?
What is the default password for HP Procurve switch?
Using the Console Setup screen
| Parameter | Default |
|---|---|
| Manager Password | blank |
| Logon Default | CLI |
| Time Zone | 0 (none) |
| Community Name | public |
How do I reset my HP switch 1910?
Steps I took so far;
- Connect switch cable to COM.
- Open Putty on COM 38400 – 8 – 1 – N.
- Powercycle the switch.
- Press Ctrl-B at boot to enter extended boot menu.
- Skip current system configuration.
- Reboot.
How do I log into my HP switch?
On the computer connected to the new HP Switch you need to: Open a browser software, enter the IP address of your Switch and access the HP Switch web interface. On the prompt screen, enter the administrative login information. After a successful login, the administrative menu will be displayed.
How do I access the HP v1910 switch?
Type the IP address http://169.254.1.2 in the address bar and press Enter. The login page of the web interface appears: b. Enter the username admin and the verification code (As shown in the image below. Example: T5DT), leave the password blank, and click Login.
What is the default password for HP printer admin?
Open a web browser and type the printer IP address in the address field exactly as it appears on the Configuration Page, and then press Enter. Click the Security tab, and under General Security, set the local administrator password. Keep the username default as admin. Type the New Password and Verify Password.
How do I reset the password on my HP switch?
Solution: You can clear the switch password by pressing the recessed Clear button on the front of the switch. This action deletes all password and user name protection from all of the switch’s interfaces.
How do I restore my hp to factory settings?
To execute the factory default reset on the switch, perform these steps:
- Using pointed objects, simultaneously press both the Reset and Clear buttons on the front of the switch.
- Continue to press the Clear button while releasing the Reset button.
- When the Self Test LED begins to blink, release the Clear button.
How do I restore my HP 1920 to factory settings?
To execute the factory default reset on the switch, perform these steps:
- Using a small, thin tool with blunt ends (such as a paper clip), press the Reset button on the front of the switch.
- Continue to press the Reset button until the Fault LED light begins to flash.
- Release the Reset button.
What is the default username and password for HP switch?
The default username for first time configuration is admin, no password is required. Usernames and passwords are case sensitive.
How do I setup my HP switch?
How to: Configure a HP ProCurve switch
- Step 1: Connect your serial connection.
- Step 2: Conenct PuTTY.
- Step 3: Get the IP address.
- Step 4: Set time server.
- Step 5: Set SNMP community info.
- Step 6: Launch the web GUI.
- Step 7: Configure basic info.
- Step 8: Create VLANs.
How do I show running config on HP switch?
To display the running configuration using the WebAgent:
- In the navigation pane, click Troubleshooting.
- Click Configuration Report.
- Use the right-side scroll bar to scroll through the configuration listing.
How do I assign an IP address to my HP 5130 switch?
WebAgent: configuring IP addressing Click on Quick Setup. In the Switch Quick Setup Parameters box, click on Change. Enter the IP address and any other information such as the Subnet mask and Gateway. Click on Save to save changes.
What’s the default username and password on HP ProCurve 2610 switch?
We had to clear the passwords on one of our HP Procurve 2610 switches and now I cannot get into the “Security” section of the web interface. I’ve scoured the web to find what the default username and password are (the credentials we had set before the clear no longer work) and have tried numerous combinations such as:
How to enable password recovery on hp v1910 je009a?
HP V1910-48G JE009A Factory reset – Password recovery capability enabled. 08-05-2016 12:27 AM 08-05-2016 12:27 AM HP V1910-48G JE009A Factory reset – Password recovery capability enabled. I have got a HP V1910-48G JE009A on my desk without any credentials. This switch needs te be set to factory defaults. 7. Skip current system configuration 0.
Is the HP 1920 series switch a ProCurve switch?
This is not a ProCurve switch, it runs a flavor of Comware. HP supports both switch lines, but they are vastly different. They are however, just as easy to setup if you are familiar with them, and from an end-user perspective, once setup, you cannot tell the difference.
Why is my HPE OfficeConnect 1910-48g je009a reverted to default?
If your HPE OfficeConnect 1910-48G (JE009A) has been reverted by you to its default…why do you think your Switch hasn’t (at least) the local admin user configured by default?