What is master slave and cable select?
What is master slave and cable select?
All IDE drives have jumpers that select the “master” or “slave” role on the controller, but modern drives also have a “CS” or “Cable select” pin. This allows the IDE cable itself to select the drive’s role: all the drives have the CS jumper set, and the cable chooses the master and the slave.
What does cable Select mean?
Cable select, also referred to by the acronym CS, is a disk drive jumper setting which automatically sets the priority of a disk drive by its position on its data cable. When cable select is enabled, the drive configures itself as a primary or secondary depending on its position in the drive chain.
What is a master slave jumper?
If a jumper connects pins five and six, which are the center pins on each row, it is a master. If the jumper connects pins three and four, which are the pins second to the right, it is a slave.
What is master and slave in bios?
How to Configure Master and Slave in BIOS for Two Hard Disk Drives in a Single System. “Master” drives typically store the operating system, while “Slave” drives are used for additional storage and backup.
How do I make a master slave drive?
Answer: You simply set the jumper to Cable Select on both drives and depending on where you connected them to the cable the computer would know which is Master and which is Slave. If you are going to use Cable Select you need a special 40 conductor IDE cable that would determine master and slave connections.
How do I make a SATA drive master and slave?
Plug one end of a SATA data cable into the smaller L-shaped connector on the hard drive, and plug the other end into one of the SATA controllers on your computer’s motherboard. The SATA controllers are usually labeled SATA1, SATA2 and so on.
For what can we use IDE connector?
Integrated Drive Electronics (IDE) is a standard interface for connecting a motherboard to storage devices such as hard drives and CD-ROM/DVD drives. The original IDE had a 16-bit interface that connected two devices to a single-ribbon cable.
What is IDE configuration?
IDE—This setting makes the SATA drive act like PATA (IDE) hard disk drives that were once common in Windows-based systems. When this setting is used, the SATA drive can’t use advanced features, such as native command queuing and hot-plugging, and SATA 3Gbps and 6Gbps drives run at only 1.5Gbps.
How do I make a master-slave drive?
How do I change from slave to master in BIOS?
Steps
- Restart your computer.
- If prompted for a password, enter it and press the “Enter” key.
- Navigate to the “CMOS Setup” and press “Enter”.
- In the CMOS menu, find “Hard Disk” and then the “Primary Master” selection.
- Move the cursor to the “Primary Slave” selection and press “Enter” again.
- Edit step.
How does the IDE cable select the slave role?
All IDE drives have jumpers that select the “master” or “slave” role on the controller, but modern drives also have a “CS” or “Cable select” pin. This allows the IDE cable itself to select the drive’s role: all the drives have the CS jumper set, and the cablechooses the master
Where does the cable connect to the slave drive?
After changing the jumpers, connect the hard drive cable from the motherboard to the hard drives. Under normal circumstances, the end of the drive cable attaches to the Master hard drive, while the inside connector on the cable connects to the Slave drive. What About Cable Select?
What happens if I set both cable to master?
If you set both drives on the same cable to master or slave then the computer most likely won’t recognize the drives in the BIOS and therefore you won’t be able to boot the computer with the drive or install your operating system on it. So always check your settings when installing a new drive.
How does IDE drive select master or slave?
This constant moving of the power and data cables plus moving the master/slave drive jumper was getting very old very fast, but we have found a great solution. All IDE drives have jumpers that select the “master” or “slave” role on the controller, but modern drives also have a “CS” or “Cable select” pin.