What is Cisco Access Point?
What is Cisco Access Point?
A wireless access point (WAP) is a networking device that allows wireless-capable devices to connect to a wired network. It is simpler and easier to install WAPs to connect all the computers or devices in your network than to use wires and cables.
How do I configure a Cisco router as an Access Point?
Cisco Wireless Access Points – Cisco Workgroup Bridges: Cisco Unified Wireless Network Configuration Example
- Enter the SSID name, VLAN ID, and the RADIO interface.
- In the Client Authentication Settings area, check the Open Authentication check box.
- Leave all other parameters with their default values.
- Click Apply.
What is air CAP3702I a K9?
AIR-CAP3702I-C-K9 is one of the 3700 series AP, needing wireless controller, providing internal antenna and C regulatory domain. 4 x 4 MIMO (multiple-input multiple-output) technology with three-spatial-stream offers a greater coverage for more reliability and capacity than competing access points.
What is the range of Cisco Access Point?
Barring physical obstruction and radio interference, Cisco Meraki access points equipped with omnidirectional antennas typically reach 100 meters. Directional antennas (sometimes called “panel antennas”) greatly extend range by concentrating power in a single direction.
What is the purpose of access point?
An access point is a wireless network device that acts as a portal for devices to connect to a local area network. Access points are used for extending the wireless coverage of an existing network and for increasing the number of users that can connect to it.
How does a access point work?
Access points work by connecting direct to your broadband router or network switch with a Ethernet or data cable. This provides the AP with the internet connection and bandwidth required. It then transmits and receives a wireless signal in either the 2.4Ghz or 5Ghz frequency range (WIFI).
How do I setup a router as an access point?
HOW TO SETUP ACCESS POINT
- Step 1:Connect the router to your existing router via an Ethernet cable.
- Step 2:Attach the new router’s (to be used as AP) power cable to the rear Power port and wall electrical outlet.
- Step 3:Wait until the device initializes.
- Step 4:For example, the IP address might be ‘192.168.
How do I log into my access point?
Open the web browser and type the IP address of the access point/extender (Default is 192.168. 1.1/192.168. 1.254/192.168. 0.254) into the address bar and then Press Enter.
Is access point better than extender?
An access point has the power to increase the network coverage in its designated area by 100%. A range extender is less effective, offering only about a 50% network coverage increase. Range extenders are a more cost-efficient option for individuals.
How does the access point work?
Does access point reduce speed?
That’s to say, because access points don’t decrease the internet bandwidth, hence zero adverse impact on the internet speed. It doesn’t matter if you are using multiple devices and routers to create a connection (even if it’s on different floors), the access point shouldn’t impact the internet speed.
What are the features of Cisco 3700 series access points?
The 3700 series provides high reliability and overall wireless performance. The 3700 series offers dual-band radios (2.4 GHz and 5 GHz) with integrated and external antenna options. The access points support full inter-operability with leading 802.11ac clients, and support a mixed deployment with other access points and controllers.
What kind of radio does a 3700 access point have?
The 3700 series access point contains two simultaneous dual-band radios, the 2.4-GHz MIMO radio and the 5-GHz 802.11ac MIMO radio. The 3700 series access point configurations are:
What kind of radio does the Cisco 3702e have?
For information on the regulatory domains, see “Regulatory Domains” section. The 3702E model is configured with up to four external dual-band dipole antennas, and two 2.4-GHz/ 5-GHz dual-band radios. The radio and antennas support frequency bands 2400–2500 MHz and 5180–5865 MHz through a common dual-band RF interface.
What does CAPWAP stand for in Cisco Aironet?
CAPWAP is a standard, interoperable protocol which enables an access controller to manage a collection of wireless termination points. The discovery process using CAPWAP is identical to the Lightweight Access Point Protocol (LWAPP) used with previous Cisco Aironet access points.