Which is a better axle Dana 35 or AMC 20?
Which is a better axle Dana 35 or AMC 20?
The AMC 20 has a better starting point then the Dana 35. The ring gear is larger then a Dana 44’s ring gear. Yes the tubes are weak and will bend (I know!!!) under heavy stress.
How do you tell if I have a Dana 35?
There are a few things that can help you tell if the axle is a Dana 35 or a Dana 44. The easiest way to tell these axles apart is to look at the shape of the differential cover. The Dana 35 cover is pretty much perfectly round. The Dana 44 is sort of a six-sided shape.
Is a Dana 35 worth building?
Make no mistake, a built Dana 35 is a strong and capable axle. Obviously not as strong as a build Dana 44 (or similar), but if you’re not going to be running anything larger than 33″ tires, a built Dana 35 should suit you just fine.
What is the difference between a Dana 30 and Dana 35?
a Dana 30 is a front axle. A Dana 35 is a rear axle (unless you are talking about Ford axles, which you aren’t). The parts are not interchangeable.
Is the Dana 60 a good axle?
Like we said above, the Dana 60 is the stronger axle. If you want to run big tires or big power you need a Dana 60 axle. At the same time, the Dana 44 is a great axle if you don’t need giant tires or big power. Most people don’t realize how heavy a Dana 60 is and how much unsprung weight affects handling.
Is the Dana 44 strong?
It used to be that the Dana 44 was considered to be a fairly stout axle. But as trails got tougher and tires got larger, the 44 got dumped in favor of even stronger hardware. But the Dana 44 is a pretty stout piece, and many companies offer parts to make your 44 even stronger than it now is.
Can a Dana 30 Handle 35 inch tires?
Yes. A Dana30 with 30-spline shafts will be fine for 35″ tires.
Is Dana 30 strong?
The 30 has been proven as a good little axle as long as the tires stay under 36″ or so. Like I said, I run 35’s, 4.88’s, full locker and the stroker and I beat the piss out of it and have had almost no problems with it.
Can a Dana 35 handle 35s?
Yes, a built Dana 35 with a Super35 kit installed can handle 35s.
Are Dana 30 axles good?
Is Dana 60 a ton?
One thing that’s confusing about the Dana 60 axles is that a Dana 60 in front is usually considered a 1 ton axle, and a Dana 60 in the rear is usually considered a 3/4 ton axle. This is most likely because the rear axle in a truck carries more weight than the front (when loaded).
How much horsepower can a Dana 60 handle?
The 23-spline axle from our 1968-vintage Dana 60 is 1/4-inch thicker in the spline area. The beefier Dana 60 axles and diff can handle up to 200 more horsepower than the 8 3/4, but not more than about 650 hp with slicks at the strip.
What’s the difference between a Dana 35 and 8.25?
Long story, but what are the major differences to consider when swapping between the Dana 35 and the Chrysler 8.25, or visa versa? I’ve gotta yank my 8.25 in favor of the D35 for a short term fix. U-Joints the same? Drive shaft same length?
What are the axle shafts on a Dana 35?
The tubes measure 2.6 inches thick which is pretty small. The Chrysler 8.25 has a three-inch tube diameter, so keep that in mind if you upgrade your rear axle. Last but certainly not least: the axle shafts. The Dana 35 axle shafts have 27 splines and a 1.18-inch diameter.
Which is better a Mopar 8.25 or a Dana?
The 8.25″ seems to have a little flatter profile at the top and bottom as well as the raised channel along the rim (which was a PITA to clean the RTV out of). I never expected a reply so quickly.
Can you change drive shaft from Dana 35 to D44?
I went from a d35 to d44 in a buddy’s driveway in an evening. I had new u bolts ready to go and the brakes were all set, shocks just bolted up the same too… U joint should be 1310 on both and the pinion length shouldn’t be different enough to change your drive shaft.